How to do A pour over Coffee: step-by-step guideline
Pour over is one of the best brewing methods in which one can control the extraction process more and receive a deliciously flavorful and aromatic cup of coffee. Here’s how to do it:
Equipment you will be needing
-
Pour-over Brewer
This is such as V60, Chemex or Kalita Wave.
-
Coffee Filter
Such as paper and metal depending on the brewer you are working with
-
Coffee Grinder
Again, a burr grinder is recommended as it produces uniform grind for all.
-
Coffee Scale
Not very crucial but quite helpful for accurate measurement.
-
Kettle
The gooseneck kettle is handy to control water flow
-
Fresh Coffee Beans
Choose your favorite roast
-
Hot Water
Preferably at 195°F to 205°F (90°C to 96°C)
-
Coffee Mug or Carafe
To collect the brewed coffee.
-
Coffee Amount
For every 6 oz of water you will add 1 -2 tbsp approximately 15-30 g, and adjust quantity relative to individual preferences.

Step-by-Step Steps
Step 1: Measure and Grind Coffee
- Measure Coffee: Using approximately 20-24 grams of coffee for a regular cup, around 12 oz.
- Grind Coffee: Grind your coffee to a medium-coarse consistency – roughly sea salt in texture. Freshly grinding your coffee will yield you the best flavor.
Step 2: Prepare Your Equipment
- Brewer Setup: Prepare your pour-over brewer to set atop your mug or carafe.
- If you’re using a paper filter, place one of these into the brewer; then rinse the brewer with some hot water to remove paper flavors from the brewer, and warm up your brewer. Throw out the rinse water.
Step 3: Add Ground Coffee to Filter
- Add the ground coffee into the filter. Spread it evenly so that it can extract evenly.
Step 4: Heat Water
- Boil: The water is boiled to an active boil of 195 to 205 degrees F or 90 to 96°C, or you can bring the water to the boiling point, and then let it cool about 30 seconds.
Step 5: Bloom the Coffee
- Hot water: Pour- just enough to wet them (which is always double the weight of the coffee, for example, 40 – 50 ml of hot water is used in relation to 20 grams of coffee).
- Let your coffee bloom for about 30 seconds and allow the carbon dioxide gas to be released that will thrill your taste buds.

Step 6: Continuous Pouring
- Steady drips of water: Once you have achieved a bloom, pour the hot water in a circular motion over the grounds. Stir to try to get as even a saturation of grounds as possible.
- Add enough to have enough for your serving of brewed coffee, such as 12 ounces.
Filtration method
Add final water. Pour in a circle out and back to the center. This guarantees there is extraction sufficient.
Step 7: Let It Drip
- Let the Coffee Drip: Let the drip happen after you have added the final water. There should be normally 3-4 minutes total drip time if you provided a 1-minute bloom time.
Step 8: Pour and Enjoy
- Pour Brewer Off: Once the coffee has stopped dripping, pour the brewer off of the mug or carafe.
- Throw Out Used Coffee Grounds and Filter: Toss out the grounds that have completed the brewing cycle and dispose of the used filter.
- Pour and Enjoy: Pour-over coffee is now drinkable. You can have it black or to taste with milk, cream, and even a sweetener.
Pour-Over Coffee: How to Brew the Best
Experiment with Ratios
Try your ratio to find the best one for you.
Fresh Coffee
For great flavor use fresh roasted beans. But grind only just before brewing for maximum freshness.
Water Temperature
Don’t let water get too hot. It tastes bitter. Too cool, and it won’t extract properly.
Practice the pouring technique
The more you practice in pouring, the better your technique will turn out to be and this, in turn, will make way for consistent brew.

Conclusion
For pour-over coffee, you will really be getting the rewarding method of crafting a great-tasting cup of coffee with care and precision. Just with enough practice, you can fine-tune just how you will make it according to your own taste preferences to achieve a nice, satisfying, and flavored brew. You will enjoy not just the finish but also the process.
